Open

Product by Category > Geotextiles > ACETex® Reinforcement


Use & Purpose

  • Reinforcement
  • Separation

Highlights

  • High strength up to 1200kN/m
  • Large range to suit the application
  • Proven for use in Main Roads works
  • Quality Certified
  • Stocked in Australian warehouses
  • Wide-width rolls

General Information

Road and geotechnical design engineers are facing an increasing challenge throughout Australia of building roads, mining platforms and other infrastructure works on very problematic soils. Previous treatments might have involved very expensive excavation and replacement techniques, surcharging the site and waiting extended periods of time for increases in strength though pore water dissipation and consolidation or abandonment of the site option through cost. ACETex® provides engineers with a cost effective, proven alternative

ACETex® geotextiles are polymer based geotextiles that are manufactured specifically for applications of soil reinforcement. Generally the engineering application for the product will determine the most suitable type of geotextile that should be selected for use by the designer or contractor.

ACETex® woven geotextile is used where very high strength reinforcement of soil is required such as under embankments.

Product Information

ACETex® woven geotextiles are manufactured from the extrusion of a polymer (polypropylene or polyester) into either a flat tape or filament product which may be then further processed by slitting or bundling and then weaving to form a fabric.

ACETex® woven geotextiles are ideally suited for applications of reinforcement or separation as the strength of the tape or filament within the fabric may be increased to suit a specific application. ACETex® woven geotextiles additionally have the ability to develop high strengths at relatively low strains which is a very important requirement in applications of reinforcement. Fabric strength is manufactured in two directions and may be varied to suit a particular reinforcement application. In applications of reinforcement and where a load may need to be sustained by the geotextile for significant periods of time the choice of polymer used in the construction of the fabric will determine the choice of woven product. The influence of creep effects on varying polymer types is well understood and will have a marked influence on the load carrying capability of the geotextile selected.

Applications

In applications of soil reinforcement the use of engineered geotextiles allows significant tensile strength to be imparted to soils. Soils are very weak in tension.  The ACEtex® geotextile effectively “bridges” potential failure planes behind or below structures that normally would require require significant additional cost to construct. The
use of soil reinforcement techniques has proven to be a very cost effective method of construction.

Soil Reinforcement in Applications of:

  • Embankment support over soft soils
  • Embankment support over soft soils with wick drain treatment
  • Embankment support over piles
  • Support over voids
  • Load Transfer Platforms

ACETex® woven geotextile is suitable for use in short term as well as very long term ground support applications with design lives in excess of 120 years. The product may be manufactured for site specific requirements. The rolls are available in wide widths up to 5.2m to minimise wastage from overlap requirements.

Global Synthetics offer a range of woven geotextiles for applications of separation and reinforcement. . The ACETex® geotextile range (polyester) of products is used for primary applications of reinforcement over extended periods of time. Typically the strength range of this product is between 100 kN/m to 1200 kN/m.




Latest Posts

March 14th, 2024

Sustainable engineering solutions for natural disaster rehabilitation, recovery and resilience – Part 2

Review of Part 1: The Engineering solutions for natural disasters include: (1) sustainable engineering solutions for quick and economical yet technical and durable rehabilitation and repair of...

Read More
February 22nd, 2024

An Effective and Economic Solution to Ground Improvement

With the rapid growth of population and economy, the development of public projects often has no choice but to encounter the poor ground with insufficient stability or excessive subsidence or...

Read More
February 16th, 2024

Sustainable engineering solutions for natural disaster rehabilitation, recovery and resilience – Part 1

Introduction The Engineering solutions for natural disasters include: (1) sustainable engineering solutions for quick and economical yet technical and durable rehabilitation and repair of the...

Read More
October 3rd, 2023

Sustainable Geosynthetic solutions for wind farms

The urgency to transition to renewable energy sources has intensified as global energy demands continue to rise. Wind farms are gaining momentum as an effective solution to combat climate change and...

Read More


If you would like further information
about any of our products please

Contact Us
Contact Us